Chamberlain liftmaster professional инструкция по программированию на русском

WARNING

WARNING

To prevent possible SERIOUS INJURY or DEATH from electrocution:

• Be sure power is not connected BEFORE installing the receiver.

To prevent possible SERIOUS INJURY or DEATH from a moving

gate or garage door:

• ALWAYS keep remote controls out of reach of children. NEVER

permit children to operate, or play with remote control transmitters.

• Activate gate or door ONLY when it can be seen clearly, is properly

AVERTISSEMENT

adjusted, and there are no obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed.

NEVER permit anyone to cross path of moving gate or door.

AVERTISSEMENT

WARNING

PREPARATION

Set Power Supply Voltage

CAUTION

The use of 24V with the jumper in 12V position will cause permanent

damage to the receiver.

The receiver can be powered with either 24V AC/DC or with 12V

DC. The jumper must be in the 24V position for use with 24V,

and in 12V position for use with 12 VDC. The jumper must be set

to the proper voltage to avoid damage to the receiver.

AVERTISSEMENT

The receiver is factory set at 24V. Figure 1.

Set Security Mode

The 312HM Universal Receiver can be used with up to 15

ATTENTION

315 MHz rolling code transmitters or passwords in HIGH security

mode. Alternately, it can be used with up to 31 of any type 315

MHz transmitter in NORMAL security mode, including any

combination of rolling code, billion code, or dip switch remotes.

The jumper must be set at the HIGH position for the receiver to

operate in HIGH security mode. It must be set at NORMAL

position to operate at the NORMAL mode. Figure 2.

When changing from NORMAL to HIGH security mode, any

previous transmitter codes must be erased. Repeat Steps 2 and

3 on Side 2 to reprogram the receiver for each remote control

transmitter in use.

The receiver is factory set at HIGH.

Set Output Duration

(Commercial Applications ONLY)

WARNING

To prevent possible SERIOUS INJURY or DEATH, the use of

CONSTANT OPERATION on residential openers is PROHIBITED.

CAUTION

For commercial applications, the receiver can be set for either

constant or momentary closure on the output contacts. Use of

constant closure is prohibited on residential garage door openers

because it overrides the safety reversal devices.

With the jumper in the «M» (Momentary) position, the contacts

will close for 1/4 second regardless of the length of radio

transmission. With the jumper in «C» (Constant) position,

AVERTISSEMENT

the contacts will stay closed as long as the radio continues

transmitting. Figure 3.

The receiver is factory set at M.

ATTENTION

Universal Radio Control

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of

this receiver and/or transmitter are prohibited, except for changing the code setting or replacing

the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired operation.

Jumper

Circuit

Power Supply

Board

Terminals

24V POSITION

FIGURE 1

AVERTISSEMENT

Jumper

Security Mode

Terminals

AVERTISSEMENT

HIGH

SECURITY MODE

FIGURE 2

CONSTANT

Jumper

OPERATION

Output

Duration

Terminals

FIGURE 3

OWNERS MANUAL

Models 312HM and 312HC

Circuit

Power Supply

Board

Terminals

WARNING

WARNING

12V POSITION

Security Mode

Jumper

Terminals

NORMAL

SECURITY MODE

WARNING

MOMENTARY

Jumper

OPERATION

Output

WARNING

Duration

Terminals

AVERTISSEMENT

AVERTISSEMENT

Jumper

Привод для секционных ворот LIFTMASTER 4410E оснащен встроенным радиоприемником. Память радиоприемника рассчитана для запоминания 12 пультов дистанционного управления. При утере брелка или смене владельца рекомендуется полностью очистить память радиоприемника и записать оставшиеся пульты заново.

Для очистки памяти радиоприемника:

1. Нажмите и удерживайте нажатой кнопку программирования (на задней панели привода) более 6 сек, светодиод будет гореть, а затем погаснет. Все пульты стерты. Стереть один пульт по отдельности невозможно.

Для программирования нового или дополнительного пульта:

1. Нажмите и удерживайте нажатой кнопку на пульте дистанционного управления 

2. Нажмите и отпустите  кнопку программирования на задней панели привода. Светодиод однократно мигнет.

3. Отпустите кнопку на дистанционном пульте.

Программирование окончено.

ВАЖНО: Если Вы отпустили кнопку на пульте дистанционного управления прежде, чем мигнул светодиод на панели

привода, то код не был запомнен.

Совместимы пульты: 

LiftMaster 4330Е, LiftMaster 4332Е, LiftMaster 4333Е, LiftMaster 4335Е.

 Купить пульты для электроприводов LIFTMASTER

Посмотреть инструкция для Chamberlain Liftmaster бесплатно. Руководство относится к категории Системы дистанционного открытия дверей гаража, 1 человек(а) дали ему среднюю оценку 9.3. Руководство доступно на следующих языках: -. У вас есть вопрос о Chamberlain Liftmaster или вам нужна помощь? Задайте свой вопрос здесь

Не можете найти ответ на свой вопрос в руководстве? Вы можете найти ответ на свой вопрос ниже, в разделе часто задаваемых вопросов о Chamberlain Liftmaster.

Не нашли свой вопрос? Задайте свой вопрос здесь